From:
Tim Tighe
2005-03-05 12:30:36
|
The cable that send power to drive the wheels snapped, and I don't know what part to order or how it goes own. Snapper model # 65373113 Serial # RP21501 |
From:
Kurt Weiand
2005-04-17 08:59:19
|
I need the deck belt Diagram to know how it goes on Snapper LT1848 riding mower (where do I find such info?) |
From:
Robert
2005-05-04 13:52:08
|
Snapper riding mower...the minute I release the brake, it dies???? Starts no problem. Could this be a problem due to inproper brake adjustment...or the safety switch? |
From:
tom carney
2005-05-14 23:08:02
|
I have a model 3081 and the belt snapped. The writing is worn off. I need the correct belt number and how it placed on the pulleys and which one goes where? |
From:
don mcdaniel
2005-05-22 14:11:39
|
i have been given a snappper mower model #3081s 11 horse briggs rear engine. after getting the engine going the mower will not move, eith forward or backward. i noticed that the drive wheel is not touching the pancake pulley (thats what i call for lack of proper terminology)i replaced the wheel thinking that was the problem. i have adjusted everything i can see to make it touch and drive the mower, but alas no success. can you give some suggestions to things i can adjust or replace to make the mower move? |
From:
tom
2005-05-28 12:52:03
|
my belt on my snapper mower won't tighten when i enguage it. how do i adjust the tention? |
From:
Bill Neely
2005-06-18 04:18:50
|
I have a riding snapper mower, rear engine 11 hp, model # 30085S. I'm looking to get a manual for the mower and any other info available. I dont even know how old it is. I would appreciate any help! thanks Bill |
From:
Melvin Hurston
2005-07-17 17:15:26
|
Good morning. I hope your day is going well.
I am the third owner of a Snapper rear engine 12 hp, 5 speed, Hi Vac 33, disc drive mower which works well. Hhowever, it cuts my lawn too low despite it being placed on the highest level possible. I have inflated the tires to no avail. I was told by a Snapper dealer that "Snappers are notorious for cutting too low and there is nothing you can do about it". Needless to say this was very disappointing to hear. Before I purchase another mower (which would not be a Snapper if it does not cut high enough for my tall fescue lawn), is there anything you suggest I do to increase the cutting blade height? For example, are there bigger tires available to purchase to raise the cutting height? I would appreciate any advice you have for me to address this matter.
Thank you very much.
Have a great day.
Melvin Hurston
mhurston@unch.unc.edu |
From:
SANDY
2005-08-03 08:48:26
|
MY RIDER GOES IN GEAR BUT DOESN'T MOVE
IS IT A BELT THING OR TRANSMISSION? |
From:
Ronald
2005-08-19 12:48:05
|
Trying to replace belt on Snapper Riding Lawnmower, 8 HP. Can you help? |
From:
glen
2005-08-26 15:09:07
|
i do not know were the two wires on top of the engine by the throttle go? |
From:
Jana
2005-08-27 11:52:36
|
Need to replace belt on murray 40" riding lawn mower |
From:
Larry
2005-09-10 14:26:06
|
I have the same problem as Sandy and I need to find out where to put the transmission floud in please help |
From:
L. Estes
2008-07-10 10:37:29
|
I have a new Snapper 28" cut rider. Can the blade be engaged when in reverse by somehow defeating or over-riding the safety feature? Right now it only can go in reverse if the blade is disengaged, but I need to mow in reverse in several spots in my lawn. Thanks! lestes@doe.mass.edu |
From:
2008-07-06 15:33:29
|
|
From:
sandra
2008-07-05 13:20:43
|
i have the same problem as sandy(9-01-07). i have a snapper series 23. cranks fine, but when i take my foot off the clutch, it dies. i have drained the gas and put in new. can you help me with this problem please? |
From:
Steve
2008-06-21 18:45:50
|
how do i replace a deck drive belt on a rear-engine snapper mower |
From:
Buddy Horn
2008-06-09 09:31:30
|
Snapper 10HP rear engine riding mower! Runs fine on a flat terrain! Won't pull a grade at all! Anything the layman ( me ) can do? Thanks |
From:
chya
2008-06-06 18:03:18
|
I have a snapper riding briggs rear motor, older. I have 2 questions, The brake won't work, so how can I fix that, and it cuts way to low even on high, will large wheels help? what size? we raised the deck a little, but it still cuts way too low. HELP ME PLEASE
cwbwew@aol.com |
From:
mark
2008-05-31 17:01:29
|
The manual for the rear engine Snapper I have doesn't have instructions for clutch disc replacement. My question is: How is the disc centered before tightening the bolts? |
From:
Mitch Oliver
2008-05-31 11:59:38
|
Have a 28" rider, rear 8 hp. How do I adjust the cutting blade belt? It's new but way to loose.
Thanks |
From:
Chris Breen
2008-05-25 16:06:24
|
Got a MTD 125 RH 92B model no 13DC458E600 and need a cutter belt but dont know the part no can you help |
From:
jack
2008-05-24 22:14:58
|
14 hp won't pull an incline, has rubber clutch disk and is adjusted to shift easily, whats up? tks |
From:
dave
2008-05-17 19:28:43
|
My Snapper 9.5hp rider will not go into neutral and won't drive forward or reverse.The shift lever seems to be working OK.Thanks for any advice. |
From:
clark
2008-05-04 12:53:29
|
my snapper rear engine mower won't pull it's self up small inclines. I've adjusted the clutch cable. Also is eems like I'm not getting as much power as I should |
From:
robert
2008-05-01 10:04:00
|
snapper 2000gx transmission not moving |
From:
robert
2008-05-01 10:09:56
|
Having problems engaging transmission on 2000gx snapper...forward or backward |
From:
Walter S
2008-04-30 20:08:09
|
Riding mower- Parked after last use now it wont crank and appears to not have fire to the plug. |
From:
frank
2008-04-19 17:20:55
|
Ihave a snapper walk behind 48 inch model spe140kw mower does not go for when drive is engaged . sometimes it goes forward then as soon as i have to climb any slight incline it stops going forward. |
From:
Butch Anderson
2008-04-08 20:33:36
|
I have a Snapper 281013BE runs great but the cables that adjust the rear deck are all the way up and the mower still cuts too low. I raised the timing rod 9/16 nur but that made the front too high. Any sugesstions? |
From:
William Jordan
2008-04-08 21:34:33
|
I have a 28" snapper riding mower. The shifter lever does not want to move. Have visually inspected all rods and checked grease in trans. Any info would be appreciated. (glennj@ellijay.com) |
From:
Glenn
2008-04-09 16:20:40
|
Snapper riding mower. The shifter lever will not move and it stays in 2nd gear. |
From:
tom
2007-09-26 13:01:07
|
I have a snapper rider mower goes in gear but doesn't move is there a sher pin or chain in the drive system help ? |
From:
Kathy
2007-09-01 11:38:36
|
I have a Snapper series 23 riding mower. It starts fine but dies when clutch is released. Can't find any troubleshooting for this problem. Can you help? |
From:
jerry
2007-08-06 22:30:16
|
On the snapper pancake wheel as you call it there are two set screws located on the shaft directly above that wheel. Move shift lever to park or roll position loosen set screws move pancake away from drive wheel until it just clears. Tighten set screws. Move shift lever to first or position 1 and see if pancake comes into contact with drive wheel. It should make contact in all positions except roll or neutral. With this done your snapper should move right on out and cut the grass. Hope this has helped you! |
From:
M Gilbert
2007-08-04 12:15:21
|
I have a 42" 15 hp Snapper Riding mower. The model number is HZ15420KVE. While using it the belt came off. The belt is fairly new and in good repair--where do I find directions to replace it. Taking to the repair shop is very costly. |
From:
joe croemer
2007-07-22 06:19:48
|
my snapper 2000 gx just quit. the engine runs fine, the blades turn,but will not move in either direction. what could it be? thanks. |
From:
wolfman
2007-07-22 09:29:24
|
I have asnapper rear-engine model 3081w and trying to find manual and parts can you help wolf6man9@yahoo.com |
From:
Chelle
2007-07-15 23:11:02
|
If I don't have the model number, how do I determine what the identifying information is? |
From:
john
2007-07-07 12:41:53
|
I have a 12/hp 30in rider,its getting hard to put into gear,anyone know why? jwdurden2000@yahoo.com |
From:
Steve
2007-07-06 09:23:00
|
I have a snapper riding mower with a honda 11hp engine. the engine starts great but when I release the brake the mower starts to choke out, but if I push the brake all the way down the mower runs just fine. Also, when I engage the mower blade the engine will smooth out and run just fine. Could this be a bad brake switch. |
From:
RonG
2007-06-29 16:49:29
|
My Snapper starts right up, but when put into gear and begins to move the engine stops. I took cleaned the carburator bowl of winter gel build up and the same thing still happens. I took the carburator off to make sure no float pins were lost the first time. They were there. What adjustments or help do you suggest? |
From:
hank crossman
2007-06-23 13:13:10
|
I have s snapper rider that is fairly old. Rear engine, model # 3312512be. I can see a stripped gear at the R rear wheel so I am assuming that is my problem -- the mower won't move forward/reverse at all. Repair shop wants $500 to fix it, so I'd like to try to replace the part myself. I'm having problems removing the rear axle and haven't been able to find any useful info online, so I'm hoping you can help me. I've looked in the parts manual but until I can get the dang thing off, I'm not sure which part I'll need. Any pointers on removing the rear axle are greatly appreciated. Thanks. Hank. itsmehoc@cox.net |
From:
Glyn
2008-07-21 15:55:33
|
My Snapper mower cuts too low even on the highest setting? Can anything be done? |
From:
RICHARD
2008-08-14 14:10:22
|
WHY IS MY SNAPPER REAR ENGINE RIDER HARD TO PUT IN REVERSE? |
From:
2008-12-30 15:27:59
|
snapper-cutting deck not engaging |
From:
todd
2009-02-15 12:47:44
|
my govenor is not set right how do iset it in the motor |
From:
Ben
2009-03-13 17:10:54
|
If your cutting deck is not engaging, it is probably one of 3 problems. 1. Your belt is off the pulley. 2. The spring attached to your lever that actually engages the blade is broken. OR 3. Your belt is too long for the distance btw the two pulleys. To solve this problem, a minor adjustment can be made in the length of the entire frame of the mower. Under the seat is the central shaft that attaches the front of the mower to the rear of the mower. This can be adjusted by loosening the two nuts/bolts that hold it tight, then just pull on the front of the mower until the desired length is achieved, tighten back up and go. |
From:
Randy
2009-06-13 19:45:09
|
I have a Snapper HiVac rider. Suddenly it is having trouble driving. I took the Disc off to inspect it (its a disc drive) and it looks normal. I did notice that when in gear but not moving that the rubber disc is spinning but the metal plate is not. Any idea's? |
From:
rubber boots
2009-03-22 12:23:08
|
Need diagram to replace the rubber boots on my Snapper 28 Hi-Vac 12 hp. Or can you tell me how |
From:
chris johnson
2009-05-05 18:29:22
|
I have a Snapper 28086s 28" with a 8hp Briggs, and I just love it. I recently had the power quit to the tires, so I am going to replace the smooth clutch disk. I can do that repair myself, but anything past that I will be lost.
My question is this---I took the wheels off and the disk off. I turn each end of the wheel mounts and the other wheel mount does not move. Do you think I have a broken internal chain or are these wheels not designed to turn together? I can replace the disk, but I am scared to see if chain is broken and take it any further apart. Should both wheels be turning or should I tear into to it. Thanks for any help you can offer. |
From:
John
2009-05-12 01:09:43
|
I have RP316012 lawnmower and I'm having a problem adjusting the gound to slow down. What siz is the crankshaft pulley? T engine is a B & S 12H802 2677-E1.
Your assistance ion the above matter would be greatl appreciated. |
From:
John
2009-05-12 01:11:34
|
I have RP216012 lawnmower and I'm having a problem adjusting the gound to slow down. What siz is the crankshaft pulley? T engine is a B & S 12H802 2677-E1.
Your assistance ion the above matter would be greatl appreciated. |
From:
Rockie
2009-05-26 21:55:16
|
What size bolts go on back tires of snapper mower? This mower is from the 1980"s |
From:
Steve
2009-07-07 19:55:35
|
My snapper rider has lost all power when pulling thje longer i run it the less it will pull. Seems like the belt is in good working order know smell or smoke coming from the belt or rear end. Noticed that there is a allenhead set bolt in the center of another bolt and i looked to see maybe if the fluid was dirty and it looked gray and old. What can I do to figure out what it might be that is doing this? Model #lt16oh42cbv Snapper tells me that there is know maintance requierd with these hydro static rear ends but our local snapper dealer is not the brightest bunch so please could you help me. |
From:
Jon
2009-07-14 19:47:03
|
Hell my Snapper 2000 GX just dies after about 10 to 15mins of cutting grass it has a fuel filter on the left side of the engine that keeps drying up?? it say the model number is gt180h485kv but i cant find a manual on the snapper web site |
From:
Theresa
2009-07-15 13:16:58
|
I have a snapper zero turn riding mower. It is making a grinding sound when I turn the key. I am starting it the same way I always do.....any ideas as to what the problem might be? |
From:
Lynn Morris
2009-07-28 15:20:20
|
I am trying to replace the belt for a snapper mower with a 28in deck. How do you get it on the rear pulley? |
From:
2009-08-26 20:38:26
|
Snapper will not shift into 2nd gear -- its a Series six 8.5hp model -- is it worth fixing (in good condition otherwise) |
From:
2009-09-01 09:40:54
|
blades won't engage on my snapper zero turn |
From:
mj
2009-09-02 21:01:18
|
I have a 9.0 power built snapper riding mower.It goes in reverse but not forward.Whats wrong? |
From:
RAK
2009-09-18 13:28:01
|
I have a 21" walk behind mower. The differential apperas to be locking up when I try to pull the lawnmower backwards. Also It stays engaged in pulling even when the lever for the clutch is disengaged. |
